When an engineering component needs to slide, move or support a load with minimal friction, PTFE and UHMWPE are two materials that are often considered.
Both offer low friction, good chemical resistance and self-lubricating performance. Both are used in bearings, wear strips, liners, seals and sliding components.
But they are not interchangeable.
PTFE generally offers lower friction, higher temperature capability and greater chemical resistance, while UHMWPE offers excellent abrasion resistance, impact strength and a lower material density.
So which is better?
The answer depends on what the component actually needs to do.
What is the difference between PTFE and UHMWPE?
PTFE vs UHMWPE: Key Properties
When is PTFE the better choice?
When is UHMWPE the better choice?
PTFE and UHMWPE in Subsea Bearings
Which has the Lowest Friction?
PTFE vs UHMWPE for Wear Resistance
What about Chemical Resistance?
How should you choose between PTFE and UHMWPE?
PTFE (polytetrafluoroethylene) and UHMWPE (ultra-high molecular weight polyethylene) are both high-performance thermoplastics, but their properties are quite different.
PTFE is particularly well known for its exceptionally low friction, chemical resistance and ability to operate at elevated temperatures.
UHMWPE has a very different performance profile. Its extremely long molecular chains give it excellent toughness, impact strength and abrasion resistance, making it particularly useful where a component will experience repeated sliding and wear.
For many applications, both materials can provide effective low-friction performance. The important question is which other properties matter alongside friction?
| Property | PTFE | UHMWPE |
|---|---|---|
| Friction | Extremely Low | Low |
| Abrasion Resistance | Moderate | Excellent |
| Impact Resistance | Moderate | Excellent |
| Chemical Resistance | Exceptional | Very good, but more limited |
| Temperature Capability | High | Moderate |
| Creep Resistance | Relatively Low | Better than PTFE at room temperature, but still requires design consideration |
| Moisture Absorption | Extremely Low | Very Low |
| Density | Higher | Lower |
| Machinability | Good | Good |
| Typical Strengths | Low friction, chemical and temperature resistance | Wear, impact and toughness |
*These are general material characteristics. Actual performance depends on the specific grade, counterface, load, speed, temperature and operating environment.
PTFE is often the preferred material when very low friction is the primary requirement, particularly when the component is also exposed to chemicals or elevated temperatures.
Its combination of low friction, chemical resistance and thermal stability makes it useful for applications including:
PTFE also does not require conventional liquid lubrication to provide its low-friction characteristics, which can be particularly valuable where maintenance access is difficult.
However, virgin PTFE has a significant limitation: creep.
Under sustained load, PTFE can gradually deform over time. This is particularly important for load-bearing applications where dimensional stability is critical.
This doesn't necessarily rule out PTFE. Filled and reinforced PTFE grades can be developed to improve properties such as load-bearing capability, wear resistance and resistance to deformation.
UHMWPE is particularly attractive where abrasion resistance, impact strength and toughness are more important than achieving the absolute lowest possible friction.
It is commonly used for:
UHMWPE is also considerably lighter than PTFE, which can be useful for large components.
Its excellent abrasion resistance can make it a particularly effective choice where sliding surfaces are exposed to repeated wear or abrasive particles.
Fluorocarbon's Fluorinoid® FL340 UHMWPE, for example, is used for bearings, wear strips and marine equipment. It combines low friction with high abrasion resistance and low moisture absorption.
UHMWPE is also inherently PFAS-free by polymer chemistry, which can make it an attractive option where customers are looking to reduce or avoid fluorinated materials.
Bearings are a good example of why simply comparing coefficients of friction isn't enough.
A bearing material needs to manage a combination of:
PTFE can provide exceptionally low friction, but creep and wear need to be considered when designing a bearing for sustained loads.
UHMWPE can offer better abrasion and impact resistance, making it attractive for applications where repeated wear is the dominant failure mechanism.
The correct choice therefore depends on what is causing the bearing to work hard.
A high-temperature, chemically aggressive application may favour PTFE.
A lower-temperature application involving abrasive particles and repeated impact may favour UHMWPE.
Subsea applications provide a particularly demanding example of material selection.
Bearings and sliding interfaces used around subsea pipelines, PLETs, power cables and support structures may need to accommodate movement while exposed to:
The bearing material therefore needs to do more than simply have a low coefficient of friction.
UHMWPE can be an effective material for subsea bearing applications where abrasion resistance and toughness are important.
This can be particularly valuable where sand or other abrasive particles may enter the sliding interface.
Fluorocarbon's FL340 UHMWPE is used in subsea bearing sleeper pads. The material was selected for its combination of low friction, very high abrasion resistance and resistance to marine growth.
These sleeper pads are used at pipeline and power cable crossover points, as well as in subsea buckle initiation sleeper units. They allow the supported structure to move while reducing friction and wear at the sliding interface.
PTFE is also widely used for subsea sliding bearings, particularly where very low friction, chemical inertness and predictable sliding behaviour are important.
Fluorocarbon's Fluoroglide® FL134 is a PTFE grade developed specifically for subsea bearing applications. It is designed not to support marine growth and is used in subsea sliding pads where controlled movement is required between rigid structures and supporting mud mats.
The application is not simply about reducing friction. Subsea pipelines can expand and contract as operating conditions change. If this movement is restricted, stresses can build up in the pipeline and surrounding structure.
A low-friction bearing interface allows the movement to occur in a controlled way, helping to reduce stress, abrasion and potential damage to pipeline coatings.
Subsea bearing performance can be difficult to predict from standard material data alone.
The actual system may involve seawater, sand, pressure, low temperatures, marine growth and a specific counterface material.
For this reason, Fluorocarbon can carry out project-specific friction and wear testing, including testing in seawater and with sand to simulate subsea conditions.
This is an important consideration when specifying a bearing for a long-life subsea application: material selection and bearing design should be validated against the conditions the component will actually experience.
If the only question is which material provides the lowest friction, PTFE generally has the advantage.
However, friction is not a fixed material property. It can change depending on:
Large-scale testing of engineering polymers has also demonstrated that friction and wear behaviour can change significantly with counterface and operating conditions.
This means that choosing a material purely from a published coefficient of friction can be misleading.
The important question is not simply:
“Which material has the lowest coefficient of friction?”
It is:
“Which material provides the required friction and wear performance under the actual operating conditions?”
This is an area where UHMWPE generally has a significant advantage.
Its molecular structure gives UHMWPE excellent resistance to abrasive wear, making it well suited to applications involving repeated sliding against rough surfaces or exposure to abrasive particles.
PTFE can also provide excellent wear performance when appropriately formulated with fillers or reinforcement, but virgin PTFE is not generally the first choice when severe abrasion is the dominant requirement.
This is one reason filled PTFE grades are used for demanding bearing applications. Adding fillers can improve wear resistance, load-bearing capability and dimensional stability while retaining many of PTFE's inherent advantages.
Temperature is another major differentiator.
PTFE has a much wider useful operating temperature range than UHMWPE.
This makes PTFE the more appropriate choice where the component needs to maintain performance at elevated temperatures.
UHMWPE is better suited to relatively moderate temperatures. As temperature increases, its mechanical properties and dimensional stability become increasingly important considerations.
For a bearing application, the actual temperature at the sliding interface should be considered rather than simply the ambient temperature.
Friction, pressure and sliding speed can all contribute to heat generation.
Both materials provide good chemical resistance, but PTFE has the broader chemical resistance profile.
PTFE is highly resistant to a very wide range of chemicals, making it particularly useful in aggressive process environments.
UHMWPE has good general chemical resistance, but there are environments, particularly involving strong oxidising chemicals, where PTFE is the safer material choice. Fluorocarbon's FL340 guidance, specifically identifies oxidising acids as an exception to its chemical resistance.
A useful starting point is to identify the dominant engineering requirement.
| If the application prioritises... | Consider... |
|---|---|
| The lowest possible friction | PTFE |
| High abrasion resistance | UHMWPE |
| High impact resistance | UHMWPE |
| Elevated operating temperatures | PTFE |
| Extreme chemical resistance | PTFE |
| Low material weight | UHMWPE |
| Resistance to marine wear and abrasive particles | UHMWPE |
| Long-term loaded sliding with very low friction | PTFE or a reinforced PTFE grade |
| PFAS-free material | UHMWPE |
| A combination of low friction and high wear resistance | Application-specific PTFE or UHMWPE grade |
This table is a starting point rather than a universal rule. The correct material depends on the complete operating envelope.
PTFE and UHMWPE are both valuable low-friction engineering materials, but they solve different problems.
Choose PTFE when very low friction, chemical resistance or temperature capability are the main priorities.
Consider UHMWPE when abrasion resistance, impact strength, toughness, low weight or PFAS-free material selection are more important.
For demanding bearing applications, the decision may become more complex. Filled PTFE, UHMWPE and other engineering polymers can all offer advantages depending on the load, speed, temperature, environment and expected service life.
This is particularly true for subsea applications, where the material must perform reliably in seawater and potentially abrasive conditions for many years with limited access for maintenance.
Ultimately, the best low-friction material is not necessarily the one with the lowest coefficient of friction. It is the one that provides the right combination of friction, wear resistance, mechanical performance and environmental stability for the application.
Fluorocarbon manufactures and machines a range of PTFE, filled PTFE and UHMWPE materials for bearings, sliding components, wear parts and other demanding engineering applications.
Our engineers can help assess the load, movement, temperature, environment, counterface and required service life before recommending an appropriate material or bearing solution.
For subsea applications, project-specific friction and wear testing can also be carried out to replicate conditions such as seawater and abrasive sand.
If you're choosing between PTFE and UHMWPE for a low-friction application, the right material selection starts with understanding how the component will actually operate.
PTFE is well known for its exceptionally low friction, excellent chemical resistance and wide operating temperature range but when a component needs greater wear resistance, load-bearing capability, dimensional stability or resistance to deformation, a filled PTFE grade may provide a better solution.
PTFE is known for its excellent chemical resistance, low friction and wide operating temperature range. But it also has a limitation that engineers need to consider carefully: PTFE can creep under sustained load.
PTFE has long been one of the most widely used high-performance polymers in engineering. Its combination of low friction, excellent chemical resistance, non-stick properties and broad operating temperature range makes it difficult to replace. But there are situations where PTFE may no longer be the best choice; we explore why and what can be a suitable alternative.
Structures, pipelines and heavy industrial equipment rarely remain completely static. Thermal expansion, contraction, seismic movement, vibration and differential movement can all introduce forces that need to be accommodated within the design. For applications involving high loads and relatively slow movement, PTFE slide bearings provide a simple and highly effective way of controlling this movement while minimising friction and maintenance requirements.
Fluorinoid® FL100 is a virgin PTFE (polytetrafluoroethylene) material offering excellent chemical resistance, very low friction, excellent electrical insulation properties and high thermal stability.
Wafer Carriers protect some of the world's most valuable products throughout manufacturing, ensuring delicate silicon wafers remain free from damage, particles and contamination. Every clip, support, spacer and structural component within these trays must be manufactured to exceptional standards because even microscopic imperfections can reduce wafer yield.
While a rotary shaft seal is relatively small, its performance directly affects equipment reliability, vacuum integrity and particle generation. Find out why how Fluorocarbon engineered a bespoke flanged seal that significantly improved equipment performance for a leading semiconductor OEM.
At Fluorocarbon, we manufacture large diameter compression moulded billets up to 1300mm in diameter, giving engineers access to oversized polymer stock that can be machined into complex components while maintaining exceptional material integrity.
Valve seat failure is one of the most common causes of leakage, unplanned maintenance and reduced equipment reliability in oil and gas operations.
When manufacturing high-performance PTFE components, the quality of the starting material is just as important as the machining process itself. Internal stresses within PTFE can lead to distortion, movement during machining, and dimensional instability, making it difficult to achieve the tight tolerances required in critical applications.
In the oil and gas industry, sealing materials operate in some of the harshest environments found in engineering. High pressures, aggressive chemicals, sour gas exposure, temperature extremes, and rapid pressure fluctuations can all compromise seal integrity and lead to costly equipment failures.
In today's manufacturing environment, engineers and procurement teams face increasing pressure to reduce risk, shorten lead times, improve performance, and simplify supply chains. Whether developing a replacement for an opalescence material for aerospace components, or designing hydrogen infrastructure applications, material selection and component design have become more interconnected than ever.
While production technologies capture the headlines, the long-term reliability of hydrogen systems often depends on the performance of the materials operating behind the scenes.
In oil and gas operations, where equipment runs continuously in some of the harshest environments on earth, reliability is everything. Unplanned downtime can cost operators hundreds of thousands per hour, impact production targets, and create significant safety risks.
In the oil and gas sector, sealing components operate under some of the toughest conditions on earth. Extreme pressures, corrosive chemicals, broad temperature swings and the constant risk of downtime. Selecting the right material is critical for safety, efficiency and long-term reliability.
The oil and gas industry operates at the intersection of extreme loads, harsh environments and zero-tolerance for failure. From topside decks and jackets to subsea structures, every moving or sliding interface must deliver predictable, low-friction performance across decades.
Renewable energy infrastructure must endure some of the harshest conditions on Earth. Offshore wind farms face relentless salt spray, extreme temperature shifts, and high mechanical loads.
The global energy landscape is evolving rapidly. Hydrogen, solar, and wind energy are no longer niche technologies, they are central to achieving a cleaner, more sustainable future.
The global shift toward hydrogen as a clean energy source brings exciting opportunities and equally demanding engineering challenges.
As the world accelerates toward cleaner energy, hydrogen has emerged as a key player in the global transition. Among the challenges, effective sealing stands out as a critical factor, and this is where advanced polymers make the difference.
In the aerospace industry, reliability is non-negotiable. From protecting components against extreme temperatures to ensuring long-lasting performance in corrosive or high-stress environments, coatings play a vital role in aircraft and spacecraft systems.
The aerospace industry demands materials and components that can withstand extreme conditions while delivering reliability, efficiency, and safety.
The aerospace industry is evolving at a rapid pace. From reusable spacecraft to ever-smaller, high-performance satellites, the demands placed on materials have never been greater.
When it comes to aerospace engineering, every gram counts. Whether in the skies or beyond Earth’s atmosphere, weight reduction, durability, and reliability are mission-critical.
The semiconductor industry relies on some of the most advanced technologies in the world to create the tiny, complex circuits that power everything from smartphones to satellites.
In semiconductor manufacturing, wet process systems play a critical role in wafer cleaning, etching, and surface preparation.
In aerospace engineering, where every gram matters and reliability is non-negotiable, material selection can mean the difference between flight and failure.
In high-stakes industries such as oil and gas, renewable energy, semiconductor, and aerospace, the choice of material isn’t just a technical decision, it’s a business-critical one.
As the demand for smaller, faster, and more powerful electronic devices continues to grow, the semiconductor industry constantly seeks more precise, efficient, and contamination-free manufacturing techniques.
As the world accelerates toward decarbonisation, hydrogen is emerging as a critical enabler of the clean energy transition.
PTFE (also referred to as Teflon), is known for its exceptional resistance to chemicals and high temperatures, making it an ideal choice for sealing applications in harsh environments. PTFE gaskets and washers are suitable for various sealing applications.
PTFE (also referred to as Teflon) is extremely resistant to the elements. Unlike other plastics’ UV resistance that can become brittle and crack when exposed to UV radiation, PTFE remains flexible and durable, making it ideal for many applications.
Updated 29/01/2026 Polytetrafluoroethylene, PTFE, or Teflon® as it is often referred to, is a tough, ductile material with excellent thermal properties and outstanding resistance to chemicals and the passage of electric current. PTFE has an exceptionally low coefficient of friction, believed to be lower than any other solid.
We bust some common myths around PTFE, including processing techniques, recycling, properties and uses.
When machining PTFE it’s essential to design your application with PTFE’s inherent properties in mind, it can be difficult to achieve tight machining tolerances. At Fluorocarbon, we utilise our in house compression moulding capabilities to create stock shapes for efficient machining of custom PTFE parts.
Updated 12/02/2026 Fluoropolymers share several unique properties which make them suitable for use in the automotive, aerospace, oil and gas and medical industries. PTFE, PFA and FEP are the most well-known and common fluoroplastics. So what, exactly, are their differences?
Updated 12/02/2026 Two of the most frequently specified materials are PTFE and PEEK. Understanding their differences is critical when specifying components such as seals, valve seats, bearings, insulators or structural parts.
Updated 10/02/2026 The fundamental difference between PTFE and PCTFE lies in their chemical structure. In PCTFE, one fluorine atom in the polymer backbone is replaced with a chlorine atom. This seemingly small change results in significant differences in mechanical strength, thermal performance, processability, and end-use applications.
PTFE is a tough, non-stick, low friction material. Because of its flexibility PTFE can creep and deform under heavy loads but this can be alleviated by adding filler.
PTFE is a tough, non-stick, low-friction material, but due to its flexibility, PTFE can creep and deform under heavy loads. This can be alleviated by adding filler.
Fluoroglide® Slide Bearings are superior to conventional expansion plates, rollers and rocker arms, because they accommodate expansion and contraction, as well as other reciprocating motions of thermal, seismic or differential…
What is PTFE coating? PTFE (Polytetrafluoroethylene), the original fluoropolymer, is a tough yet flexible, material with great electrically insulating properties and excellent resistance to chemicals; it has one of the lowest coefficients of friction of any solid.…
High-Performance Plastic, High-Temperature Plastic, High-Performance Thermoplastic, High-Performance Polymer…However you refer to this range of materials, what makes them different to other types of plastic?
Ultra-High Molecular Weight Polyethylene (UHMWPE) is a high-performance engineering thermoplastic known for its exceptional wear resistance, toughness, low friction and impact strength. UHMWPE is a type of polyethylene with exceptionally long molecular chains. These long chains become highly entangled, giving the material a distinctive combination of toughness, abrasion resistance and durability that is difficult to achieve with conventional polyethylene grades.
Updated 10/02/2026 PTFE/Teflon: Properties, Structure, and Performance Explained Polytetrafluoroethylene (PTFE) is a tough, flexible, non-resilient thermoplastic best known for its exceptional chemical resistance, outstanding thermal stability, and extremely low coefficient of friction.…